Kann mir jemand einen Hinweis geben und erkären was ich falsch gemacht habe?
Ich habe volle Verbindung zu allen Rechnern und die Routen für die Netzwerke zum Provider und der West Region werden auch nicht verteilt.
Habe aber Trotzdem nur 71 Punkte.
Folgende Angaben:
[
Link nur für registrierte Mitglieder sichtbar. Bitte einloggen oder neu registrieren ]
Zitat:
Interface IP Netmask Gateway
E-Branch1
Fa0/0 192.168.0.1 /25 255.255.255.128 N/A
Fa0/1 192.168.0.129 /25 255.255.255.128 N/A
S0/0/0 192.168.1.250 /30 255.255.255.252 N/A
S0/0/1 192.168.1.245 /30 255.255.255.252 N/A
E-Branch2
Fa0/0 192.168.1.1 /26 255.255.255.192 N/A
Fa0/1 192.168.1.65 /26 255.255.255.192 N/A
S0/0/0 192.168.1.254 /30 255.255.255.252 N/A
S0/0/1 192.168.1.246/30 255.255.255.252 N/A
EPC1 192.168.0.2 /28 255.255.255.128 192.168.0.1
EPC3 192.168.1.2 /26 255.255.255.192 192.168.1.1
NetAdmin 192.168.1.66 /26 255.255.255.192 192.168.1.65
Step 1: Configure the Device Basics.
Note: Initially, you can only access router E-Branch2 through the console connection on NetAdmin.
a. Configure the following on E-Branch2:
• The router name is EB2.
• The privileged EXEC mode uses the following encrypted password: class.
• Enable Telnet and console line logins and use the following password: cisco.
• Configure the banner message-of-the-day as Authorized access only!
b. Using the Addressing Table, configure and activate all the necessary interfaces on E-Branch2.
c. Configure correct host IP addressing.
• Configure EPC2 with the last IP address in the subnet.
• Configure EPC4 with the last IP address in the subnet.
Step 2: Discover the Network.
a. Explore the network to determine the IP address of the serial interface that EastHQ uses to connect toE-Branch2.
b. Remotely access EastHQ.
Step 3: Configure Static and Default Routing.
a. Configure connectivity to the West Region.
• Configure a static route on EastHQ to the entire West Region. The West Region uses the 172.16.100.0/24address
space. Use the next-hop address argument.
• Configure a default route on EastHQ to send to the Internet all other traffic for destinations that are not found in the
EastHQ routing table. Use the exit interface argument.
b. Verify static and default routing.
Step 4: Configure EIGRP Routing.
Configure EIGRP on EastHQ, E-Branch1, and E-Branch2.
a. Use AS number 100.
b. b.Do not advertise the network between EastHQ and the Internet.
c. Do not advertise the network between EastHQ and the West Region.
d. Advertise all other attached networks.
e. Disable automatic summarization.
f. Disable EIGRP updates out interfaces where thereare no EIGRP neighbors available.
g. On EastHQ, enter the one command in the EIGRP routing process that will propagate the default and static
routes to E-Branch1 and E-Branch2.
Step 5: Modify the default EIGRP operation.
a. Configure the link between EastHQ and E-Branch2 so that the correct bandwidth of 384 k/s is used inEIGRP
calculations.
b. Configure E-Branch1 to advertise a summary route for the subnets 192.168.0.0/25 and 192.168.0.128/25 to
EastHQ and E-Branch2.
c. Configure E-Branch2 to advertise a summary route for the subnets 192.168.1.0/26 and 192.168.1.64/26to
EastHQ and E-Branch1.
Step 6: Verify Full Connectivity.
Although these are not scored, the following connectivity tests should be successful.
• Test connectivity to the West Region.
• Test connectivity to the Internet.
|
Hier die Config der Router vor der Abgabe:
EB1:
EB2:
EastHQ:
CCNA ERouting PT Practice SBA EIGRP Hilfe
Linear-Darstellung
